24-Port 10/100Mbps + 2-Port Gigabit TP / SFP Managed 802.3at PoE Switch

Physical Port
　　• 24-Port 10/100Base-TX Fast Ethernet ports with IEEE 802.3af / IEEE 802.3at PoE injector
　　• 2 10/100/1000Base-T TP combo interfaces
　　• 2 1000Base-X mini-GBIC/SFP slots, shared with Port-25 and Port-26
　　• Reset button for system management
　　• 1 RS-232 male DB9 console interface for Switch basic management and setup

Power over Ethernet
　　• Complies with IEEE 802.3af / IEEE 802.3at Power over Ethernet End-Span PSE
　　• Up to 24 IEEE 802.3af devices powered
　　• Up to 11 IEEE 802.3at devices powered
　　• Supports PoE Power up to 15.4 watts / 30 watts for each PoE port
　　• Auto detect powered device (PD)
　　• Circuit protection prevent power interference between ports
　　• Remote power feeding up to 100m
　　• PoE Management
　　　–IEEE 802.3af and IEEE 802.3at mode switch control
　　　–Total PoE power budget control
　　　–Per port PoE function enable/disable
　　　–PoE Admin-mode control
　　　–PoE Port Power feeding priority
　　　–Per PoE port power limit
　　　–PD classification detection
　　　–Over Temperature Protection function
　　　–Temperature Threshold Control
　　　–PoE Usage Threshold Control

Layer 2 Features
　　• Prevents packet loss flow control
　　　–IEEE 802.3x pause frame flow control for full-duplex mode
　　　–Back-Pressure Flow Control in half-duplex mode
　　• High performance of Store-and-Forward architecture, runt/CRC filtering eliminates erroneous
　　　packets to optimize the network bandwidth
　　• Broadcast / Multicast / Unicast storm control
　　• 8K MAC address table, automatic source address learning and ageing
　　• Supports VLAN
　　　–IEEE 802.1Q Tag-based VLAN
　　　–Port-Based VLAN
　　　–Q-in-Q tunneling
　　　–GVRP for dynamic VLAN Management
　　　–Private VLAN Edge (PVE / Protect Port)
　　• Supports Link Aggregation
　　　–up to 13 trunk groups
　　　–up to 8 ports per trunk group with 1.6Gbps bandwidth (full duplex Mode)
　　　–IEEE 802.3ad LACP (Link Aggregation Control Protocol)
　　　–Cisco ether-channel (Static Trunk)
　　• Spanning Tree Protocol
　　　–STP, IEEE 802.1D (Classic Spanning Tree Protocol)
　　　–MSTP, IEEE 802.1s (Multiple Spanning Tree Protocol, spanning tree by VLAN)
　　• Port Mirroring to monitor the incoming or outgoing traffic on a particular port

Quality of Service
　　• 4 priority queues on all Switch ports
　　• Traffic classification
　　　–IEEE 802.1p CoS
　　　–IP TOS / DSCP to 802.1p priority mapping
　　　–Port-Based priority
　　• Strict priority and Weighted Round Robin (WRR) CoS policies
　　• Supports QoS and In/Out bandwidth control on each port
　　• In/Out rate limit control on each port

Multicast
　　• Supports IGMP Snooping v1 and v2
　　• IGMP Snooping v2 fast leave
　　• Querier mode support

Security
　　• IEEE 802.1x Port-based network access control protocol
　　• RADIUS users access authentication
　　• L3 / L4 Access Control List (ACL)
　　• Source IP-MAC / Port-Binding
　　• Port Security for Source MAC address entries filtering

Management
　　• Switch Management Interface
　　　–Telnet Command Line Interface
　　　–Web switch management
　　　–SNMP v1, v2c, v3 switch management
　　　–SSL switch management
　　• Three user privilege levels control (Admin, Operator, viewer)
　　• DHCP client for IP address assignment
　　• DHCP Option82 and DHCP Relay
　　• Link Layer Discovery Protocol (LLDP) for easy network management
　　• Built-in Trivial File Transfer Protocol (TFTP) client
　　• Firmware upgrade via TFTP or HTTP
　　• Configuration restore / backup via TFTP or HTTP
　　• Event message logging to remote Syslog server
　　• Alarm records extractable in standard CSV format for post processing
　　• Four RMON groups 1, 2, 3, 9 (history, statistics, alarms, and events)
　　• SNMP trap for interface Link Up and Link Down notification
　　• Supports Ping function
　　• Supports Simple Network Protocol (SNTP)

24-Port 10/100Mbps +2 Gigabit TP/SFP Combo Managed PoE Switch

Physical Port
• 24-Port 10/100Mbps Fast Ethernet ports with PoE Injector
• 2 10/100/1000Mbps TP and SFP shared combo interfaces
• RS-232 male DB9 console interface for switch basic management and setup
• Reset button for system management

Power over Ethernet
• Complies with IEEE 802.3af Power over Ethernet End-span PSE
• Up to 24 IEEE 802.3af devices powered
• PoE Power up to 15.4 watts for each PoE port
• Auto detects powered device (PD)
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100m
• PoE Management
　–Total PoE power budget control
　–Per port PoE function enable/disable
　–PoE port Power feeding priority
　–Per PoE port power limit
　–PD classification detection

Layer 2 Features
• Complies with the IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z Gigabit
　Ethernet standard
• Supports auto-negotiation and full-duplex / half-duplex modes for all 10Base-T / 100Base-TX and 1000Base-T ports
• Auto-MDI/MDI-X detection for each RJ-45 port
• Prevents packet loss Flow Control:
　–IEEE 802.3x pause frame flow control for full-duplex mode
　–Back-Pressure Flow Control in Half-Duplex mode
• High performance of Store-and-Forward architecture, runt/CRC filtering eliminate　erroneous packets to optimize the network bandwidth
• Broadcast / Multicast / Unicast storm control
• 8K MAC address table, automatic source address learning and ageing
• VLANs
　–IEEE 802.1Q Tag-based VLAN
　–Port-based VLAN
　–Q-in-Q tunneling
　–Up to 255 VLANs groups, out of 4041 VLAN IDs
• Link Aggregation
　–up to 13 trunk groups
　–up to 8 ports per trunk group with 1.6Gbps bandwidth (full duplex mode)
　–IEEE 802.3ad LACP (Link Aggregation Control Protocol)
　–Cisco ether-channel (static trunk)
• Spanning Tree Protocol
　–STP, IEEE 802.1D (Classic Spanning Tree Protocol)
　–RSTP, IEEE 802.1w (Rapid Spanning Tree Protocol)
• Port mirroring to monitor the incoming or outgoing traffic on a particular port

Quality of Service
• 4 priority queues on all switch ports
• Traffic classification:
　–IEEE 802.1p CoS
　–IP TOS / DSCP to 802.1p priority mapping
　–Port-Based priority
• Strict priority and Weighted Round Robin (WRR) CoS policies
• QoS and In / Out bandwidth control on each port

Multicast
• IGMP Snooping v1 and v2
• IGMP Snooping v2 fast leave
• Querier mode support

Security
• IEEE 802.1x Port-based network access control protocol
• RADIUS users access authentication
• L2 / L3 / L4 Access Control List (ACL)
• MAC Filtering and Source IP-MAC / Port-Binding
• Port Security for Source MAC address entries filtering

Management
• Switch Management Interface
　–Console / Telnet Command Line Interface
　–Web switch management
　–SNMP v1, v2c switch management
　–SSL switch management
• DHCP client for IP address assignment
• Built-in Trivial File Transfer Protocol (TFTP) client
• Firmware upgrade via TFTP or HTTP
• Configuration upload / download via TFTP or HTTP
• Four RMON groups 1, 2, 3, 9 (history, statistics, alarms, and events)
• SNMP trap for interface Link Up and Link Down notification
• Ping function

24-Port 10/100Mbps PoE Web Smart Ethernet Switch

Physical Port
• 24-Port 10/100Mbps Fast Ethernet ports with PoE Injector
• Reset button for system management

Power over Ethernet
• Complies with IEEE 802.3af Power over Ethernet Mid-Span PSE
• Up to 24 IEEE 802.3af devices powered
• Supports PoE Power up to 15.4 watts for each 802.3af PoE port
• Auto detects powered device (PD)
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100m

Layer 2 Features
• Auto-MDI / MDI-X detection on each RJ-45 port
• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• Supports VLAN:
　–IEEE 802.1Q Tag-based VLAN
　–Port-based VLAN
　–MTU VLAN (Multi-Tenant Unit VLAN)
• Supports Link Aggregation
　–up to 2 trunk groups
　–up to 4 Fast Ethernet ports per trunk group
　–IEEE 802.3ad LACP (Link Aggregation Control Protocol)
• Supports Spanning Tree Protocol
　–STP, IEEE 802.1D (Classic Spanning Tree Protocol)
　–RSTP, IEEE 802.1w (Rapid Spanning Tree Protocol)
　–Loopback Detection
• Port mirroring to monitor the incoming or outgoing traffic on a particular port

Quality of Service
• 2 priority queues on all switch ports
• Traffic classification:
　–Port-based priority
　–IEEE 802.1p based priority
　–IP TOS / DSCP based priority
　–TCP / UDP Port-based QoS
• Strict priority and Weighted Round Robin (WRR) CoS policies
• In/Out rate limit control on each port
• Broadcast Storm Control support

Multicast
• Supports IGMP Snooping v1 and v2

Security
• MAC address filter
• TCP & UDP filter on each port
• Management idle time security

Management
• Remote Web interface for Switch management and setup
• Supports SNMP v1
• Supports DHCP Option 82 and DHCP Relay
• Firmware upgrade through Web interface
• Configuration upload / download through Web interface
• Reset button for system reboot or reset to factory default

16-Port 10/100/1000Mbps 802.3at PoE+ Ethernet Switch

Interface

• 16-Port 10/100/1000Mbps Gigabit Ethernet RJ-45 ports
• Each port supports 52V DC power to PoE Powered Device

Power over Ethernet

• Complies with IEEE 802.3af / IEEE 802.3at Power over Ethernet
• Up to 16 IEEE 802.3af / IEEE 802.3at devices powered
• Supports PoE Power up to 30 Watts for each PoE port
• Auto detect powered device (PD)
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100m

Switching

• Hardware based 10/100/1000Mbps auto-negotiation and auto MDI/MDI-X
• Flow control for full duplex operation and back pressure for half duplex operation
• Integrates address look-up engine, supporting 8K absolute MAC addresses
• 9K Jumbo Frame supports at all speed (10/100/1000Mbps)
• Automatic address learning and address aging
• Supports Pre-Energy-Efficient Ethernet (EEE) function (IEEE 802.3az)

Hardware

• 19-inch desktop size, 1U height
• LED indicators for PoE ready and PoE activity
• Ethernet Link Energy-Saving technology
• Link down power saving
• Intelligent scales power based on cable length

8-Port 10/100Mbps 802.3at PoE Desktop Switch

RJ-45 Interface
　• 8-Port 10/100Mbps Fast Ethernet
　• 8-Port supports 52V DC power to PoE Powered Device

Power over Ethernet
　• Complies with IEEE 802.3af / IEEE 802.3at Power over Ethernet End-Span PSE
　• Up to 8 IEEE 802.3af / IEEE 802.3at devices powered
　• Supports PoE Power up to 30 watts for each PoE port
　• Auto detect powered device (PD)
　• Circuit protection prevents power interference between each port
　• PoE Usage Alarm LED
　• Remote power feeding up to 100m

Switching
　• Hardware based 10/100Mbps auto-negotiation and auto MDI/MDI-X
　• Flow control for full duplex operation and back pressure for half duplex operation
　• Integrates address look-up engine, supporting 2K absolute MAC addresses
　• Automatic address learning and address aging
　• Supports Energy-Efficient Ethernet (EEE) function (IEEE 802.3az)

Hardware
　• 12-inch desktop size, 1U height
　• LED indicators for PoE ready, PoE activity and PoE Usage Alarm
　• Fanless design

8-Port 10/100/1000Mbps Web Smart PoE Switch

Generic Features

• Complies with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base- T, IEEE 802.3z Gigabit SX / LX
• 8 10/100/1000Mbps Gigabit Ethernet ports
• 2 mini-GBIC / SFP slots, shared with Port-7 and Port-8
• Each Switching ports support auto-negotiation-10/20, 100/200 and 1000/2000Mbps
• Auto-MDI / MDI-X detection on each RJ-45 port supports CSMA / CD protocol
• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• 8K MAC address table, automatic source address learning and ageing
• 16Gbps switch fabric, non-blocking switch architecture
• 9K Jumbo Frame supports all speed (10/100/1000Mbps)

Power Over Ethernet

• Complies with IEEE 802.3af Power over Ethernet standard
• All Copper ports with IEEE 802.3af injector built-in
• Supports 48V DC, 15.4-watts PoE power output to 8 IEEE 802.3af compliant Powered Devices
• Power feeding On / Off and priority configuration
• Power Limit function for PoE power management
• Powered Device Auto Detection
• LED PoE Status Monitoring

Layer-2 Switching

• Supports Port-based and IEEE 802.1Q VLAN function, up to 64 VLAN groups
• IEEE 802.1w Rapid-Spanning Tree protocol supported
• Link Aggregation supports static mode and LACP (IEEE 802.3ad) - up to 4 Trunk groups, each trunk with up to a maximum of 8 ports

Multicast

• IGMP Snooping for multicast filtering, supports v1 and v2
• IGMP Query Mode supports for multimedia application

Quality of Service

• 4 QoS classes per port
• Traffic class assignment based on IEEE 802.1p tag, or DSCP field
• Multicast and Broadcast Storm Control as well as Flooding Control

Security

• Port Mirroring supports dedicated port monitoring
• IEEE 802.1X Port-based access control, RADIUS Server Authentication
• Static MAC Address assigns destination MAC address at specific port

Management

• Remote Web management interface
• Firmware upgrade through Web interface
• Cable Diagnostics technology
• Supports SNMPv1 with RFC-1213 / 1573-Interface group and RMON Group 1 (Statistics)
• SNMP Trap
• Supports PLANET Smart-DISCOVERY Utility for deploy management

16-Port 10/100Mbps + 2 Gigabit TP / SFP Combo Web Smart PoE Switch

• Complies with the IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z　Gigabit Ethernet standard
• 16-Port 10/100Mbps + 2 Gigabit TP / SFP Combo Web Smart PoE Switch
• 8-Port support 48VDC power to PoE Powered Device (Port 1 to port 8)
• Each Switching ports support auto-negotiation-10/20, 100/200Mbps (Fast Ethernet) , 1000/2000Mbps (Gigabit Ethernet) supported
• Auto-MDI / MDI-X detection on each RJ-45 port
• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x　pause frame flow control (full-duplex)
• High performance Store and Forward architecture, broadcast storm control,　runt / CRC filtering eliminates erroneous packets to optimize the network bandwidth
• 4K MAC address table, automatic source address learning and ageing
• 2.75Mb embedded memory for packet buffers
• Remote Web interface for Switch management and setup
• SNMP Trap for alarm notification of events
• Broadcast Storm Control support
• Supports up to 16 / 18 port-based VLAN groups / 32 IEEE 802.1Q VLAN groups / MTU VLAN
• Supports up to 2 Trunk groups, each trunk for up to maximum 4 port with 800Mbps bandwidth
• Supports QoS , bandwidth control and MAC address filter / TCP & UDP filter on each port
• Supports port mirroring function and IGMP Snooping v1 / v2
• PoE power Disable/Enable and PoE power consumption monitoring by management interface
• Firmware upgrade through Web interface
• Password setting, IP setting and device description setting through Planet Smart discovery utility
• 19-inch rack mount size
• Internal full-range power supply suitable for worldwide use
• EMI standards complies with FCC, CE class A

8-Port 10/100Mbps 802.3at PoE Desktop Switch

RJ-45 Interface
　• 8-Port 10/100Mbps Fast Ethernet
　• 8-Port supports 52V DC power to PoE Powered Device

Power over Ethernet
　• Complies with IEEE 802.3af / IEEE 802.3at Power over Ethernet End-Span PSE
　• Up to 8 IEEE 802.3af / IEEE 802.3at devices powered
　• Supports PoE Power up to 30 watts for each PoE port
　• Auto detect powered device (PD)
　• Circuit protection prevents power interference between each port
　• PoE Usage Alarm LED
　• Remote power feeding up to 100m

Switching
　• Hardware based 10/100Mbps auto-negotiation and auto MDI/MDI-X
　• Flow control for full duplex operation and back pressure for half duplex operation
　• Integrates address look-up engine, supporting 2K absolute MAC addresses
　• Automatic address learning and address aging
　• Supports Energy-Efficient Ethernet (EEE) function (IEEE 802.3az)

Hardware
　• 12-inch desktop size, 1U height
　• LED indicators for PoE ready, PoE activity and PoE Usage Alarm
　• Fanless design

4-Port 10/100Mbps 802.3af/at PoE + 1-Port 10/100Mbps Desktop Switch (60 Watts)

■　RJ-45 Interface
　　○　Five 10/100Mbps Fast Ethernet ports
　　•　Four ports support 56V DC power to PoE Powered Device
　　•　One 10/100Mbps uplink port

■　Power over Ethernet
　　○　Complies with IEEE 802.3at / af Power over Ethernet Mid-Span PSE
　　○　Up to 4 IEEE 802.3at / af devices powered
　　○　Supports PoE Power up to 30 watts for each PoE port
　　○　60-watt PoE Budget
　　○　Auto detects powered device (PD)
　　○　Circuit protection prevents power interference between ports
　　○　Remote power feeding up to 100m

■　Switching
　　○　Hardware based 10/100Mbps Auto-Negotiation and Auto MDI/MDI-X
　　○　Flow control for Full Duplex operation and back pressure for Half Duplex operation
　　○　1536bytes packet size support
　　○　Integrates address look-up engine, supporting 1K absolute MAC addresses
　　○　Automatic address learning and address aging

■　Hardware
　　○　Desktop palm size
　　○　LED indicators for PoE ready / activity and LINK / ACT
　　○　One DC 56V power jack